Page 5
Installation Manual Pyramid Universal Dome Interface
THE UNIVERSAL DOME INTERFACE
The Pyramid Universal Dome Interface (UDI) enables a range of dome products to be connected and controlled via
the Pyramid network with a minimum of effort. The UDI can be configured to operate in a number of different dome
protocols, and because of this it can translate commands from the Pyramid network to the correct format for the
specific product.
The UDI is compatible with domes manufactured by Baxall, AD/Sensormatic, Vista, Dennard, JVC, Mark Mercer,
Panasonic, Pelco, Ultrak, Vicon and VCL. It is also compatible with Baxall CDR and CDH cameras.
It is necessary to have a UDI for each individual dome camera that is added to the Pyramid network. Usually, the UDI
will be located at the dome position. However, if a unidirectional transmission method is being used between the
dome and UDI (i.e., a radio link), then the UDI can be located at the matrix location. The UDI is also flexible in that it can
be operated from any +12V DC or 24V AC power supply capable of providing 100mA. Furthermore, the UDI is capable
of receiving four alarm inputs, and these inputs can be configured as all normally-open or all normally-closed using
a dip switch on the module.
There are three variants of the UDI, based on the speed and type of Pyramid network they use. Other than this, there
are no external or operating differences between the three variants. The PY-UDI-L runs on a low speed (9.8k b.p.s.)
RS485 network while the PY-UDI-HR runs on a high speed (78k b.p.s.) RS485 network. The third variant, PY-UDI-H,
runs on a high speed (78k b.p.s.) FTT10 network.
The figure below shows a typical system layout when a UDI is connected:
Power Supply
Pyramid Telemetry (i.e., RS485, FTT10)
Pyramid Module
e.g. Pyramid 2 Keyboard)
Dome Camera Telemetry (i.e., RS485)
DOME DATA
+
-
+
-
Rx
Tx
SERVICEDOME SELECTI ON12V DC
24V AC
1234
PYRAM ID DATABIAS
ALARM I/P
11234C
+
-
T
NO
NC
+
-
+
-
Rx
Tx
Up to 4
Alarm
Inputs
SYNC
POWER
9 - 15V
SERIAL 1
SERIAL 2
SERIAL 3 SERIAL 4
SERIAL 5 SERIAL 6
SERIAL 7 SERIAL 8
M/S INTERFACE
PRINTER
48M16
NETWORK
ON
1 3 5 7 9 11 13 15
246810121416
17 19 21 23 25 27 29 31
18 20 22 24 26 28 30 32
33 35 37 39 41 43 45 47
34 36 38 40 42 44 46 48
12
34
56
78
910
11 12
13 14
15 16
Video Connection between Dome Camera and
Pyramid Matrix (to enable image viewing)
UDI
Connection
Panels
Typical UDI Layout
Manufacturer Models UDI Software Version
Dennard 2050 Series V2.08
JVC TK-C675, TK-C676 V2.08
Mark Mercer D150, D250, D500 V2.08
Panasonic 850 Series V2.08
Pelco Spectra II and III (D-Type Protocol) V2.08
Ultrak KD6, KD6Z V1.03 or V2.08
VCL Orbiter, Jupiter V1.03 or V2.08
Vicon Surveyor V7, Surveyor 2000 V1.03 or V2.08
Baxall Pro Dome series 2.17
AD/Sensormatic SpeedDome, DeltaDome, 2.17
UltraDome series
Vista/Baxall PowerDome/CDH and CDR Cameras 2.17
(20 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce